How To: Device that stops back feeding the Grid from wind/solar

I’ve read a few Internet posts regarding people who want to self install Solar or Wind energy systems and would prefer to not power the Grid or give free electricity to their energy company. These installations may be small and not wish to invest in upgrading their meter to support back feeding the Grid.

I did a quick search and didn’t find anything simple that would do the job. Looking for a small device that can be installed in the meter box or at the entry point to a small setup, ie workshop with Solar panels and Grid* inverter then 240V equipment connected to inverter, this would allow a personal workshop to pull power from Solar when available and from GRID when not available or using larger tools.

* ALL solar setups that connects to Mains must use a specialized GRID inverter to sync the AC waveform to the GRID. So that the inverter boosts or amplifies the AC Wave. Connecting a normal Inverted to AC Mains will immediately pop the fuse or much worse.

This is where DIODES come in. A diode isn’t to convert AC to DC, while the correct design of 4 diodes will convert AC into wobbly DC, that doesn’t mean that all Diodes will do the same.

AC is a signwave that is the exact replication of a motor turning, as this is how it is generated in very large installations. The AC Wires swap every 1/50 of a second, as if someone was swapping a battery around every 1/50 of a second.

With a Diode we can direct current flow to only 1 direction. With DC, stopping a charging port from also discharging back to the charger is easy, 1 single Diode will do the job, however with AC, we need to do almost the same as the GRID Inverter, the Diodes need to swap as the AC Waveform swaps, every 1/50 of a second, at Zero Volts, the Diodes must swap to follow the current, or in our case, stop the current from flowing in a certain direction.

Below is a quick Schematic of the diodes and switches. The switch wouldn’t be a manual switch, as below, a semiconductor circuit would be used with a microcontroller to monitor the AC Waveform and swap as required.

Screen Shot 2016-02-21 at 1.20.28 PM

The Diodes and electronic switches need to be sized for the expected current, any microcontroller on todays market would do the processing without issue. Expected cost to be around $150 or less for those with enough parts laying around.

At some stage in the future, I intend to build the above and demonstrate for a small 200W Solar install and mini Grid inverter, the ones on ebay that plug into the power. Showing a Fridge running from Solar and when the fridge is off, no current feeding back into the grid. – David Robinson


Transporting a Boat + Trailer from Sydney to Ballina

Need: Transport Trailer + Boat that is unregistered to Ballina from Sydney.

Trailer capacity is 1067KG. Supports 17-19ft boats.

Quotes: $900. Truck goes every week. However needs to be booked in by Monday.
Toddtrans $100 ph on tilt back truck. – Sent online contact quote request. – Sent online contact request. – Sent online contact.

Need to get a Unregistered Vehicle Permit (UVP) Cost is paperwork time + Permit fee: $21.
Tyres are looking old and tired. Need pumping up. Will need to be careful for 800KM trip. Will need spare, if none available.
Car Hire. Avis is the cheapest. $388.80.  Main cost is the $200 for leaving it at another place.
Additional Time:
Cutting off lock with angle grinder. 1h + 2h travel time.
Pickup rental car. 1 h
Drop off rental car. 1h.
Paperwork for UVP if at RTA. 2h.
Fuel for vehicle SYD->BAL $100?

Estimated Total Cost: $490 + possibility of replacement tyres + time to prep. vs $900 for delivery to Ballina Depot and I can pickup at Ballina and carefully drive it the last few KMs with Farm car.

Monthly cost $530? at storage location.
Best Option:
$900 is a good price. No stress about replacing tyres, paperwork and time prepping. They will pickup at self storage, drop off at Ballina.

Car Quote